Sunday 15 April 2012

MOCK QUESTION PAPER: APPLIED THERMODYNAMICS (2 units only)

                                                                   Paper Code: EME-402



B.  Tech - ME
(SEM.IV) Sessional Examination, 2011 – 12
Applied Thermodynamics
Time:   3hrs                        Total Marks:  100
    Note:   (1)           Attempt all questions.
         (2)  Be precise in your answer.
SECTION-A:
Q.1: Answer the following questions as per the instructions.           
2X10=30
 (i) What is the importance of feed pump in steam engine?

(ii) What is reversible adiabatic process?

(iii) Explain the term isothermal compressibility?

(iv) What is missing quantity?

(v) What is Work Ratio in Carnot vapour cycle?

(vi) Explain the term “Specific steam consumption.”

(vii) What is thermal efficiency of a steam engine?

(viii) What is indicated power?

(ix) What is mean effective pressure of a steam engine?

(x) What is inversion temperature?

SECTION-B:
Q.2: Answer any three parts of the followings:     
                                                                                                               3X10=30
a) Derive the Tds equations.

b) Derive the expressions of mass discharge of steam through a Nozzle.

c) A single cylinder double acting steam engine is supplied with dry and saturated steam at 11.5 bar and exhaust occur at 1.1 bar. The cut-off occurs at 40% of the stroke. If the stroke equals 1.25 times the cylinder bore and engine develops 60 kW at 90 rev/min. Determine the bore and the stroke of the engine. (Assume hyperbolic expansion and diagram factor of 0.79.)
Also calculate the theoretical steam consumption

d) Dry saturated steam enters a steam nozzle at a pressure of 12 bar and is discharged at a pressure of 1.5 bar. If the dryness factor of the discharged steam is 0.95, what would be the final velocity of the steam? Neglect initial velocity of steam.
If 12% heat drop is lost in friction, find the % reduction in the final velocity.

SECTION C:
Q.3: Answer any two parts of the following: 
                                                                                         5X2=10
a) Explain the term “Joule-Thomson coefficient.”

b) With proper diagrams explain the term nozzle efficiency.

c) Explain the Clausius Clapeyron equation. Also write their field of application.

Q.4: Answer any one part of the following:   
                                                                                           1X10=10
a) Explain the effect of velocity and pressure in the flow of a nozzle. What is a choked flow? Also explain the concept of critical pressure in isentropic flow through nozzle.

b) Steam at a pressure of 20 bar, 250°C expands in a convergent-divergent nozzle up to the exit pressure of 2 bar. Assuming a nozzle efficiency of 0.94 for supersaturated flow up to the throat and nozzle efficiency as 90%, find (i) velocity at throat, (ii) mass flow rate if the throat diameter is 1 cm and (iii) velocity and diameter of the nozzle.

Q.5: Answer any three questions: 
                                                                         3X10=30
a) Derive the Maxwell’s Equations

b) Prove that Cp - CV = -T(∂V/∂T)p2(∂p/∂V)T.

c) Steam at a pressure of 10 bar, dry saturated enters the nozzle when exit pressure is 0.3 bar. The nozzle efficiency for the convergent position is 96% and that of the divergent portion is 92%. The throat diameter for each nozzle is 6 mm. Find the mass flow rate of steam and the exit diameter required.

d) Air enters a nozzle at 5 bar, 350°C and comes out at 0.95 bar. The efficiency of expansion through the nozzle is 92%. If the mass flow rate of air is 1.5 kg/s, determine the exit diameter of the nozzle and velocity of air at exit.