Showing posts with label semester question paper. Show all posts
Showing posts with label semester question paper. Show all posts

Wednesday 24 November 2010

QUESTION PAPER: ENGINEERING MECHANICS

Vivekanand Institute of Technology & Science; Ghaziabad
PRE-SEMESTER EXAMINATION (odd SEMESTER 2009-10)
B.Tech…first Semester

Sub Name: Engineering Mechanics Max. Marks: 100
Sub Code: EME-102 Max. Time: 3: 00 Hr

(i) This paper is in three sections, section A carries 20 marks, section B carries 30 marks and section C carries 50 marks.
(ii) Attempt all the questions. Marks are indicated against each question
(iii) Assume missing data suitably if any.

Group A

Q.1 Answer the following questions as per the instructions 2x20=20
Choose the correct answer of the following questions:

(i) The magnitudes of the force of friction between two bodies, one lying above the another depends upon the roughness of the
(a) Upper body;                 (b) Lower body
(c) Both the bodies               (d) The body having more roughness

(ii)The moment of inertia of a circular section of diameter D about its centroidal axis is given by the expression
(a) π(D)4/16               (b) π(D)4/32
(c) π(D)4/64               (d) π(D)4/4

Fill in the blanks in the following questions:

(iii)The distance of the centroid of an equilateral triangle with each side(a) is …………. From any of the three sides.
(iv)Poisson’s ratio is defined as the ratio between ……………………. and
………………………… .
(v)If two forces of equal magnitudes P having an angle 2Ө between them,
then their resultant force will be equal to ________ .

Match the following columns for the following two parts:

(vi) Match the column I to an entry from the column II:
COLUMN – I COLUMN - II
(i) BMD of an UDL(a) stored strain energy per unit volume
(ii) Resilience is(b) brittle materials
(iii) Bulk Modulus (c) parabolic in nature
(iv) Yield Point (d) volumetric stress & strain
(e) Ductile materials
(f) Shear stress

(vii) Match the Following columns:
COLUMN – I COLUMN - II
(i) Square of side (b) (p) π b4 / 64
(ii) Equilateral Triangle of side (b)(q) b4 / 12
(iii) Circle of diameter (b)(r) b4/ 36
(iv) Isosceles right angle triangle of base (b) (s) b4/(32√3)
(e) Ductile materials
(f) Shear stress

Column II gives the value of Moment of Inertia Ixx about a centroidal axis.

Choose correct answer for the following parts:

(viii) Statement 1:
In stress strain graph of a ductile material, yield point starts at the end of
the elastic limit.

Statement 2:
At yielding point, the deformation becomes plastic by nature.

(i) Statement 1 is true, Statement 2 is true.
(ii) Statement 1 is true, Statement 2 is true and they are unrelated with
each other
(iii) Statement 1 is true, statement 2 is false.
(iv) Statement 1 is false, Statement 2 is false.

(ix) Statement 1:
It is easier to pull a body on a rough surface than to push the body on
the same surface.

Statement 2:
Frictional force always depends upon the magnitude of the normal force.

(i) Statement 1 is true, Statement 2 is true.
(ii) Statement 1 is true, Statement 2 is true and they are unrelated with
each other
(iii) Statement 1 is true, statement 2 is false.
(iv) Statement 1 is false, Statement 2 is false.

Choose the correct word/s.
(x) Two equal and opposite force acting at different points of a rigid body
is termed as (Bending Moment/ Torque/ Couple).

SECTION-B

Q.2: Answer any three parts of the followings: 10X3=30
(a) Find the shear force and moment equation for the beam as shown in the figure. Also sketch SFD (shear force diagram) and BMD (bending moment diagram)

(b) Explain and prove “the parallel axis theorem of moment of inertia.”
Also find the centroid of the following composite area.


(c) Find the centroidal Moment of Inertia of the following shaded area.
(d) Two cylinders P and Q rest in a channel as shown in fig. below. The cylinder P has a diameter of 100 mm and weighs 200 kN, where as the cylinder Q has a diameter of 180 mm and weighs 500 kN. Find the support reactions at all the point of contact.

(e)
Two blocks A and B of weights 1 kN and 2 kN respectively are in equilibrium as Shown in the figure.
If the co-efficient of friction everywhere is 0.3, find the force P required to move the block B.

SECTION C:

(3) Answer any two parts of the following 5X2=10

(a) A simply supported beam of 2 cm wide and 4 cm high having a length 2 m long
in concentrated load of 3 kN (acting perpendicular to the axis of beam) at a point
0.5 m from one of the supports. Determine
(i) the maximum fiber stress (σb max); (ii) the stress in a fiber located at a
distance of 1 cm from the top of the beam at mid-span.

(b) Explain and justify the assumptions taken during analysis of a perfect truss.

(c)A flywheel is making 180 rpm and after 20 second it is running at 120 rpm.
How many revolutions will it make and what time will elapse before it stops, if the retardation is constant.


(4) Answer any one part of the following: 1X10=10

(a) Explain the terms angular momentum and radius of gyration.
A wheel rotates for 5 seconds with a constant angular acceleration and
describes during this time 100 rotations. It then rotates with a constant angular
velocity and during the next five seconds describes 80 radians. Find the initial
angular velocity and the angular acceleration.

(b) Analyse the following truss:



(5) Answer any three question;                           3X10=30

(a) Compare the stress – strain diagrams of a ductile material to that of a brittle Material. Also explain the term bulk modulus and modulus of elasticity.

(b) Explain and prove the “Bending Equation” (M/I)=(б/y)=(E/ρ). What is
called as Section Modulus?

(c) A cylinder of radius R, length L and total mass M is suspended vertically
from the floor, if the modulus of elasticity of the cylinder be E, find the total
deflection and maximum stress induced in the cylinder.

(d) A cylinder of 200 mm diameter is subjected to a twisting moment of
250 kN-m, the length of the cylinders is 1 m, if the modulus of rigidity of the
cylinder material be 150 GPa, find the maximum shear stress induced in the
cylinder. Also find the total angular deformation.